Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Brocas húmedas para hormigón y mampostería dura (6 pulgadas) - 1 unidad

Envío gratis en pedidos superiores a Mex $600.00

Mex $3,345.92

Mex $ 1,672 .00 Mex $1,672.00

En stock

1.Tamaño:15.24 Cm


Acerca de este artículo

  • Taño del producto: diámetro (6 pulgadas), profundidad de perforación (14 pulgadas), rosca universal (1-1/4 pulgadas), por favor confirma que coincida con la plataforma de perforación antes de realizar el pedido.
  • Dientes mejorados: a diferencia de otros productos en el mercado, el uso de versiones mejoradas de dientes reduce el ruido de trabajo y mejora la eficiencia de perforación.
  • Duradero y preciso: hecho de diante y duradero, cada producto se somete a pruebas de concentricidad minimizar la desviación de cada posición del agujero.
  • plia aplicación: brocas de núcleo hormigón, hormigón armado, bloque, ladrillo duro, asfalto, mármol y otras mamporía dura.
  • Método de taladro: taladro de mano, perforadora. Comienza a perforar desde u posición vertical y continúa cavando más profundamente. U pequeña cantidad de agua puede prolongar la vida útil. Solo para uso húmedo.



Descripción del producto

broca
broca
broca

Dean P.
Comentado en los Estados Unidos el 7 de enero de 2025
Was perfect for my needs. Needed to purchase the arbor to drive this as a separate item. Worked very well. Note: do not try to rush while using this and will work better if you use some water with it.
Hole Man
Comentado en los Estados Unidos el 29 de agosto de 2024
Core bit works great.
Don Eddington
Comentado en los Estados Unidos el 26 de mayo de 2024
I needed to drill a 2-inch hole through the edge of our concrete floor in the garage to install a 1 1/2-inch drain for a back-flush filter which runs out under the sidewalk to a 55-gallon plastic drum. I don't have a core drill (that has a water hook-up) so, I had to pour water from a plastic jug on the bit as I drilled. To get the 45-degree angle I made a 2 hole through a 2 x 6 board. When I got a few inches into the concrete, the drill hung up and slapped the crap out of me. Plan B, build a 2 x 4 brace to hold the drill with a little help from a friend. It worked great. What I learned was to drill about 1-inch at a time, pulling the drill from the hole and removing the concrete core as needed, it helped it not to get hung up. I also needed a SDS Plus adapter to go from this core bit to my rotary drill motor. Works great, Be Patient and drill slowly.P.S. when it got hung-up, we used a pipe wrench to back it out.
DAX
Comentado en los Estados Unidos el 23 de octubre de 2024
After drilling over 30 holes in 5000 PSI concrete, 4 1/2 "still going strong! I’ve put them through some seriously tough material, and they haven't let me down once.
Customer
Comentado en los Estados Unidos el 31 de enero de 2024
I ordered a 2in so as soon as i got it i had my apprentice start coring the hole , i soon realize the dam thing is a 1-1/4 not the 2 in i had order. So im goin to return. But i gota say i was a lil skeptical but it did core the hole nice and no blow out
Productos recomendados

Mex $375.41

Mex $ 172 .00 Mex $172.00

4.3
Elegir

Mex $307.51

Mex $ 138 .00 Mex $138.00

4.9
Elegir

Mex $862.19

Mex $ 405 .00 Mex $405.00

4.8
Elegir

Mex $118.13

Mex $ 66 .00 Mex $66.00

4.3
Elegir